JensenPark Posted November 22, 2008 Share Posted November 22, 2008 ok...this is a bit embarrassing: bought my CH rudder pedals about 2 months ago...just finally got around to installing them (yeah, I've been that busy with work and family). it comes with a disk with an ominous warning: Quote Link to comment Share on other sites More sharing options...
gec Posted November 22, 2008 Share Posted November 22, 2008 in short u need to tell to the IL that u have 2 joysticks. in your case joystick (or HOTAS) + pedals. this is done in config.ini here is the complete guide: http://www.mission4today.com/index.php?name=Knowledge_Base&op=show&kid=261#008 Quote Link to comment Share on other sites More sharing options...
Tonar Posted November 22, 2008 Share Posted November 22, 2008 yes what he said. I had the same problem as did everyone I think Quote Link to comment Share on other sites More sharing options...
1. DDz Quorum Sid Posted November 22, 2008 1. DDz Quorum Share Posted November 22, 2008 Don't know anything about CH stuff JP but I imagine that the CD had the pedals "driver" software on it that would be installed when the disc was inserted. With my Saitek pedals I can run them without the driver if I want but I still put it on - what I dont use with the pedals is the other software that allows you to customise the "brake" pedals etc because I can do that in the game via the "HOTAS" section at the bottom of the game's Controls section as I found there were some conflicts with other stuff. Don't worry about the ID2 stuff - that happens apparently as the pedals are recognised by the game. I found that I needed to reallocate some controls in the HOTAS section for the Saitek stick and I also found that it doesn't make any difference to the operation of the stick if it is under ID1 or ID2 anyway. Are you using the driver software for the Saitek stick? Quote Link to comment Share on other sites More sharing options...
JensenPark Posted November 22, 2008 Author Share Posted November 22, 2008 in short u need to tell to the IL that u have 2 joysticks. in your case joystick (or HOTAS) + pedals. this is done in config.ini here is the complete guide: http://www.mission4today.com/index.php?name=Knowledge_Base&op=show&kid=261#008 ok, being a complete idiot - I cannot figure this out. Quote Link to comment Share on other sites More sharing options...
1. DDz Quorum B16Enk Posted November 22, 2008 1. DDz Quorum Share Posted November 22, 2008 Kelly it sounds like your Saitek was on ID1, then your pedals snatched ID1 for themselves, putting your stick on ID2. So...in controls -> hotas section in game re-assign the aileron and elevator axis to your Saitek again Quote Link to comment Share on other sites More sharing options...
HH_RitterCuda Posted November 22, 2008 Share Posted November 22, 2008 CH uses windows driver the disk is for the programmable and to link more CH stuff under 1 controller. XP/vista link controller's alphabetically Quote Link to comment Share on other sites More sharing options...
gec Posted November 23, 2008 Share Posted November 23, 2008 yea, what besixteenenk said. proly the easiest thing would be to just reassign the stick and the pedals. Quote Link to comment Share on other sites More sharing options...
Rattler Posted November 23, 2008 Share Posted November 23, 2008 yea, what besixteenenk said. proly the easiest thing would be to just reassign the stick and the pedals. That HAS to be the most inventive translation of Roger's nick ever! , Gec - your English is still better than some native speakers! Quote Link to comment Share on other sites More sharing options...
gec Posted November 23, 2008 Share Posted November 23, 2008 Quote Link to comment Share on other sites More sharing options...
.png.3326d5bbcb89fe2bcd3937259933ad13.png)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.